Free preview
ILNAS-EN IEC 61000-6-3:2021 Edition 03/2021
Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for equipment in residential environments
  • 46.70 / copy


IEC 61000-6-3:2020 is a generic EMC emission standard applicable only if no relevant dedicated product or product family EMC emission standard has been published. This part of IEC 61000 for emission requirements applies to electrical and electronic equipment intended for use at residential (see 3.1.14) locations. This part of IEC 61000 also applies to electrical and electronic equipment intended for use at other locations that do not fall within the scope of IEC 61000-6-8 or IEC 61000-6-4. The intention is that all equipment used in the residential, commercial and light-industrial environments are covered by IEC 61000-6-3 or IEC 61000-6-8. If there is any doubt the requirements in IEC 61000-6-3 apply. The conducted and radiated emission requirements in the frequency range up to 400 GHz are considered essential and have been selected to provide an adequate level of protection of radio reception in the defined electromagnetic environment. Not all disturbance phenomena have been included for testing purposes but only those considered relevant for the equipment intended to operate within the locations included within this document. The emission requirements in this document are not intended to be applicable to the intentional transmissions and their harmonics from a radio transmitter as defined by the ITU. This third edition cancels and replaces the second edition published in 2006 and its Amendment 1:2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) alternative method for measuring conducted emissions on DC ports; b) limits and requirements applicable only to equipment intended to be used in residential locations; c) more stringent limits for DC power ports. NOTE 1 Safety considerations are not covered by this document. NOTE 2 In special cases, situations will arise where the levels specified in this document will not offer adequate protection; for example where a sensitive receiver is used in close proximity to an equipment. In these instances, special mitigation measures can be employed. NOTE 3 Disturbances generated in fault conditions of equipment are not covered by this document. NOTE 4 As the requirements in this document are more stringent or equivalent to those requirements in IEC 61000-6-4 and IEC 61000-6-8, equipment fulfilling the requirements of this document comply with the requirements of IEC 61000-6-4 and IEC 61000-6-8.


Standard - Active


Technical Committee :
CLC/TC 210 : Electromagnetic Compatibility (EMC)


start of the vote on the project    06/09/2019   date of ratification (dor)    03/09/2020
end of the vote on the project    29/11/2019   date of anouncement (doa)    26/06/2021
start of the vote on the final project    11/12/2017   date of publication (dop)    26/09/2021
end of the vote on the final project    22/01/2018   date of withdrawal (dow)    26/03/2024

Publication Official Journal
of the Grand-Duchy of Luxembourg
Reference Mémorial A N° 672


EN IEC 61000-6-3:2021/prA1:2022 (Frag 2)

Relations to older standards
ILNAS-EN 61000-6-3:2007

Relations to international standards
IEC 61000-6-3:2006/A2:201X 
IEC 61000-6-3:2006/A2:201X (CISPR/H/312/CDV) (EQV) 
IEC 61000-6-3:201X 
IEC 61000-6-3:2020 

International Classification for Standards (ICS codes) :

33.100.10 : Emission


magnifying icon

Search a standard

Advanced search


Satisfaction enquiry


Free of charge lifelong learning "Standardization"

Standards organizations

  • National standards

  • European standards

  • International standards


Your feedback is important to us!

Would you be willing to give us a short feedback?


Thank you for helping us

DIN standards can be downloaded only once! After downloading, they are no longer available in the eLibrary.
Begin download?